VIEW CART     
HOME     

DESCRIPTION

PRICE IN U.S. DOLLARS

HD Outside Corner (Male)
Has one 3/4" welded tab.
Use with a HD outside corner (female) to connect docks end-to-end. Joint requires ¾” bolt set or connector pin. Install using ½” carriage bolts.
¼” Commercial Grade

HD Outside Corner (Female)
Has two ½” welded tabs. Each Leg is 10”L x 5” H.  Install using ½” carriage bolts.
¼” Commercial Grade

$21.62

HD Special Outside Corner (Male-Female)
One leg has one 3/4" welded tab (male). The other leg has two ½” welded tabs (female).
Joint requires ¾” bolt set or connector pin. Install using ½” carriage bolts.
¼” Commercial Grade

HD Special Outside Corner (Male-Male)
Both legs each have one 3/4" welded tab (male). Joint requires ¾” bolt set or connector pin. Install using ½” carriage bolts.
¼” Commercial Grade

HD Special Outside Corner (Female-Female)
Both legs have two ½” welded tabs (female). Joint requires ¾” bolt set or connector pin. Install using ½” carriage bolts.
¼” Commercial Grade

Outside Corner End
Use this corner at ends of fingers and docks. Ideal for swim floats and ski jump corners. Each leg is 10”L x 5”H.  Install using ½” carriage bolts.
¼” Commercial Grade

$12.60

Inside Corner
This heavy duty inside corner should be used with one of the outside corners. Each leg has elongated holes for easy fit-up and is 8-1/2”L x 5”H.  Install using ½” bolts.
¼” Commercial Grade

$13.63

HD T Connector (Female)
Has two ½” welded tabs. Use with a HD male T Connector to attach fingers and ramps. Install using ½” carriage bolts.

HD T Connector (Male)
Has one 3/4” welded tab.
Use with a HD female T Connector to attach fingers and ramps. Requires ¾” bolt set or connector pin. Install using ½” carriage bolts.

Back-Up Plates
5” x 5” reinforcing plates are used to back up the single T males and females. Install using ½” carriage bolts.
¼” Commercial Grade

$3.35

Angle
Use this heavy-duty angle for all cross supports. 2-1/2”L x 5”H
Install using ½” carriage bolts.
¼” Commercial Grade

$3.55

Washer Plate
Use two washer plates with each angle.  Measures 1-1/2” L x 5” H
¼” Commercial Grade

$1.50

Splice Plates
5” x 25” splice plates are used to join timber together. Install using ½” carriage bolts. (Sold individually)
¼” Commercial Grade
 

$19.44

Left Hand Pipe Bracket
For use with 1-1/4” Galvanized pipe to help hold floating dock in place. One pipe bracket is typically mounted to a seawall or fixed dock while another is mounted on the floating dock. Install using 3/8” bolts or lags.

$16.20

Straight Pipe Bracket
For use with 1-1/4” Galvanized pipe to help hold floating dock in place. One pipe bracket is typically mounted to a seawall or fixed dock while another is mounted on the floating dock. Install using 3/8” bolts or lags.

$16.20

Right Hand Pipe Bracket
For use with 1-1/4” Galvanized pipe to help hold floating dock in place. One pipe bracket is typically mounted to a seawall or fixed dock while another is mounted on the floating dock. Install using 3/8” bolts or lags.

$16.20

Gangway Hinge Setup
(Single Hinge)
Made for use with 2x6 stringers and 5/4 decking. ¾” bolt set is included. Install using 3/8” bolts or lags.

$33.12

Phenolic Wheels
5” x 2” Black Phenolic Wheels are used for ramps. Made for use with a 3/4” diameter axle.

$20.40

Axle
3/4” x 33-1/2” HDG

$13.02

Axle
3/4” x 45-1/2” HDG

$16.95

Inside Corner Ramp Roller - Left
This heavy duty inside corner with roller assembly is used on the inside of the  lower left corner at the bottom of the ramp. Each leg has 4 holes and is 11”L x 5”H.  Install using 5/8" Hex bolts. ¼” Commercial Grade

Inside Corner Ramp Roller - Right
This heavy duty inside corner with roller assembly is used on the inside of the  lower right corner at the bottom of the ramp. Each leg has 4 holes and is 11”L x 5”H.  Install using 5/8" Hex bolts. ¼” Commercial Grade

Connector Pin Set
For quick disconnects. Used to connect male and female T connectors. Galvanized ¾” connector pin and hitch pin clip

$3.80

3/4" Hex Head Bolt Set
Includes nut. Used to connect male and female T connectors together. Galvanized. 3/4" x 3-1/2".

ChainRetainer
Bolts to side of dock. Use weights and chains to hold dock in place. Accommodates 1/4", 3/8", & 1/2" chain. Measures 5"L x 5"H

1/2 x 3 Carriage Bolt Set
Used to attach outside corners, inside corners, T-Connectors and 3" pipe holders to wood docks. 1/2" x 3" bolt, flat washer and nut. Hot dip galvanized.

1/2 x 4-1/2 Carriage Bolt Set
Used to attach outside corners, inside corners, T-Connectors and 3" pipe holders to wood docks. 1/2" x 4-1/2" bolt, flat washer and nut. Hot dip galvanized.

Angle Clip (Round)
Use this heavy-duty angle for all general connections. 2-1/2”L x 2-1/2”H Use with 1/2" Hex Head Bolts. ¼” Commercial Grade

Angle Clip (Square)
Use this heavy-duty angle for all general connections. 2-1/2”L x 2-1/2”H Use with 1/2" Carriage Bolts. ¼” Commercial Grade

Finger Deck Stabilizer Bracket
This 45/135 degree bracket reinforces diagonal lumber placed between the base of a floating finger dock and main dock to provide extra lateral support for the finger dock. Install using 1/2" Carriage Bolts. ¼” Commercial Grade